The danger of the neighborhood of the refrigerator and oven
In this article, we consider the correct location of such kitchen interior items as an oven, refrigerator or freezer. Here are the norms of the minimum distance between the individual devices and the built.In technique. We will figure out how important it is to observe permissible distances and what to do if it is impossible.
Put the refrigerator next to the oven, microwave or battery is extremely undesirable. The walls of the oven are heated during the operation of the device, the air temperature around the working plate becomes several degrees higher than in the kitchen as a whole. To cool the refrigerator, it takes more time, and the compressor in such conditions has to work without turning off longer. As a result, the refrigerator consumes more electricity and breaks faster.
Important! Compliance with the recommended distances is necessary, since in case of violation of the rules of operation, the refrigerator can quickly fail.
The neighborhood of two electrical appliances is also fire hazard. The oven placed on the refrigerator is overheated and can cause a short circuit or even fire. Devices cannot be connected to one outlet through the tee in order to avoid an increased load on the electric network. Refrigerator and oven must have grounding.
What the state should be?
The kitchen is considered a special place in the house, not only the appearance, but also convenience depends on its layout. Therefore, the correct placement of household appliances in the interior plays a huge role, in particular, this also applies to the location of the refrigerator. In some cases, a lack of area makes many owners put a refrigerator near the stove. In order to protect it from the negative consequences of high temperature, you need to know the minimum location distance, and of course, it is recommended to additionally make a protective barrier in the form of a built.In cabinet.
The refrigerator is outwardly isolated, so its location next to the gas stove will not affect the temperature mode inside, but when, the surface of the device will begin to heat up hard, the unit will work in enhanced mode. As a result of this, not only the consumption of electricity will increase, but also the load on the compressor itself, which in turn will significantly lower the life of the device. To maintain a constant microclimate and uniform cooling of the refrigerator, it is necessary to provide the maximum distance between the refrigerator and the gas stove. Otherwise, compensation for heating of the part of the device that stands near the stove will be observed. The second part of the refrigerator, which does not require cooling, will begin to freeze ice. Such temperature changes are not in favor of stored products.
In the process of cooking on its surface, the remaining fat will be expelled. Therefore, with such a “neighborhood” you will have to wash the refrigerator several times a day. To avoid this, you need to put a separation item between the device and the gas stove: the table can be a great option. In addition, thanks to the presence of a kitchen table, it will be much easier to remove and remove products.
The minimum distance between the technique is 20 centimeters. Over, this figure may change according to the recommendations of manufacturers who have certain standards for each model. So, the manufacturer Bosch advises installing a stove at a distance of 30 centimeters, and Zanussi prescribes as much as 50 centimeters.
A similar arrangement problem applies to built.In ovens or just ovens. In the instructions of any refrigerator it is written that it is strictly forbidden to install next to the heating equipment, and the oven and oven are sources of heating. Therefore, the distance between them should be at least 50 centimeters. Of course, manufacturers additionally equip the refrigerator with insulation, but it is designed to operate the device at normal temperature.
In addition, in order for the products to be cooled to the required temperature, the device will have to work more intensively and use much more electrical energy. Such a situation will accelerate the breakdown of the refrigerator, and its incorrect placement may cause warranty service in the service company, since the user did not comply with the main operating conditions. Despite this, today in many small.Sized kitchens all the same, you have to meet an oven and a refrigerator nearby. To protect the devices as much as possible, many lay a layer of thermal insulation between them, but it does not give a significant result. It is best to use built.In household appliances in this case. Thus, the oven is isolated by wooden walls, and heat is removed using an extract.
This installation causes heating the device and negatively affects the operation of the compressor, which has to work in an enhanced mode to replenish the necessary cold. And this is not only a high electricity consumption, but also the rapid wear of the technique itself. Under the influence of high temperature, the external enamel of the refrigerator can also crack, and the beautiful white surface will quickly cover the traces of fat, as a result, we will not have to talk about aesthetic form.
If we consider safety precautions, then installing the refrigerator next to the electric stove is also not allowed. Excessive overheating will negatively affect the work of the device, and a non.Standard microclimate will cause a fire. Any heat source is poorly affected by the device. In the event that the area of the kitchen does not allow you to especially arrange the technique, you need to at least adhere to the distance between the refrigerator and an electric stove of one and a half meters. It is also recommended to additionally install a protective shield or partition from thermal insulation between the technique.
What is the danger of the proximity of the slab and refrigerator?
Often, with small kitchens, people are interested in: is it possible to put a gas stove and a refrigerator nearby? Why is this neighborhood better to avoid? When working, the gas stove is very heated. Especially when the oven is on. And if household appliances stand nearby, then the heat from the stove is very heated by the walls of the refrigerator.
No Bake,No Oven,Less Maida,No Egg,Eggless Instant Refrigerator Biscuit Two Layer Cake-Kirtis Kitchen
This can cause its overheating. No wonder the manufacturers of refrigerators indicate in the instructions the distance from the stove on which various household appliances should be located. This is necessary for free air circulation. And without a gap at the stove, the refrigerator will not cool.
In addition, in some manufacturers, the grate for air circulation is on the sides of the household appliance. And it is precisely this area that will have to heat from the stove standing nearby. And this is already fraught with breakdown of the refrigerator. If its walls are not metallic, then from exposure to high temperature the paint will turn on in the place of contact with the stove. And plastic edging and pens can melt and crack. The same thing often happens with a rubber seal located in close proximity to the burners.
If the stove is standing nearby, it is inconvenient to cook on it. Long handles of pans and pots will rest against the refrigerator wall. During cooking, drops and spray often fly in all directions. Including the surface of the refrigerator. And if, due to high temperature, it begins to work in an enhanced mode, then there is a probability of a motor breakdown or a significant reduction in its service life.
Why is the refrigerator and oven not the best neighbors?
Often the owners are tormented by the question. You can put the dishwasher next to the oven? Experts believe that such a neighborhood is undesirable. On, that is, different reasons. First of all, it is the heat secreted by both devices. In the refrigerator, even in models with the NOU Frost system, the back wall is heated from the engine work. And in the oven, cooking occurs in under the influence of high temperature, so its heating is inevitable. The heat emerging from it makes the compressor work in enhanced mode. As a result, electricity consumption rises, the refrigerator wear out faster and earlier fails. At the same time, operating devices are able to heat the room hard. It will be unpleasant in the kitchen. Due to the high temperature, especially in winter, the wall covering may become unusable.
The refrigerator and oven can be placed nearby only if certain conditions are met
It is advisable to put a kitchen of household appliances separately. It is best to put a refrigerator from the edge, and another equipment in the center. Owners of small.Sized kitchen often choose a place on the insulated loggia or in the corridor. In accordance with safety measures, electrical units that release heat should stand at a distance of 50 cm from each other. If there is no other way out and they are installed too close, then a heat.Insulating layer must be laid between them and a screen of refractory glass should be laid. With improper isolation or lack of insulation in the event of a breakdown of one of the devices, the specialist will not carry out warranty repairs. Therefore, the nuances of the installation of equipment should be taken into account.
Devices that have to be built can be installed closely. All units built into cabinets and walls are isolated by partitions, equipped with special cables. The latter will prevent voltage surges. Plus built.In technology is high.Quality and reliable isolation.
Manufacturers are equipped with built.In instruments:
The most modern and expensive models have an emergency shutdown function. Models of ovens, the doors of which are equipped with triple glass, perfectly hold the heat inside the chamber. Built.In refrigerator and oven can be placed nearby.
What will happen if the oven, the oven, the plate are poorly isolated from the refrigerator. Possible consequences
The oven and the refrigerator are in contact with the side walls, the result of this largely depends on the degree of thermal insulation. If they are poorly isolated, electricity consumption increases. The refrigerator, in contact with a hot surface, begins to heat up. The sensor that is located in the chamber more often than the laid records an increase in temperature. The device begins to work with a greater load, this leads to an increase in energy consumption. At any time, a fire or closing can happen, because two devices consume a lot of energy. Due to constant overheating, sockets may well melt.
Products that are in the refrigerator quickly spoil. The ceiling, floor and wall coating spoils faster. The walls of the freezer and the refrigeration unit are not intended for them to be often washed. However, due to the close location to the plate, it is impossible to avoid the appearance of fat spots. Hence the constant untidy appearance of the refrigerator. The unit will begin to work with interruptions, freeze weakly. The compressor will be more strongly cold, and the ice form faster.
So is it possible to put an oven next to the refrigerator? It is allowed to install only in the presence of reliable isolation and compliance with certain operating rules. Due to any inconsistency of the conditions for installing the refrigerator, which are indicated in the instructions, in case of breakdown in warranty service, it may be refused.
Tips and recommendations
Here are some tips on the proper placement of devices in the kitchen
- In a small kitchen, it is best to use built.In furniture and appliances. In this case, the plate will be isolated from the refrigerator with wooden walls of furniture, and the heat from it will take the hood. The recommended gap between the devices can be disguised using sections for storage or cabinets for individual sizes.
- For a small family of 3-4 people, a standard plate can be replaced with a more compact option with two burners. This will not only increase the gap between household appliances, but also save gas consumption.
- An excellent solution for a small kitchen will be a narrow refrigerator, the width of which is less than the standard one by 5-10 cm. This will free some space for a gap.
- The transfer or replacement of the sink with a small option will significantly save the space for placing the refrigerator. Although such a sink is not very convenient, but quite practical in everyday life.
The placement of the refrigerator in the room requires compliance with important rules. The proximity of the device with the stove and other types of household appliances can be dangerous, but the situation is correctable by isolation of the unit. It should also be remembered that the proximity of the refrigerator to the heating source will lead to heat inward, which will cause an increase in the consumption of electricity and the rapid wear of the unit.
Kitchen design refrigerator next to oven
Why not put a refrigerator next to the stove
When arranging equipment in the kitchen, you should think not only about the harmonious of the interior, but also about the disadvantages of the close location of the refrigerator and heating devices.
Error: gas stove is located too close to the refrigerator
Gas stove and refrigerator
When it comes to the arrangement of kitchen equipment, many are wondering whether it is possible to put refrigerators next to gas stoves. If the kitchen is small, placing a large refrigerator on it is problematic. And compliance with all the requirements for installation sometimes becomes an almost impossible task.
It is a mistake to think that the only consequence that entails the proximity of the refrigerator and stoves is poor cooling of products. It seems to many that the situation can be corrected by setting the maximum cooling mode in the device. In fact, the warmer there is, the more actively the engine removes the heated air from the compartments. Thus, the unit with sufficient power will continue to successfully cope with its task. But on the state of its compressor, the intensive load will not affect the best way.
Normally, the refrigerator motor turns on and turns off at certain intervals. With an increase in temperature in the external environment, the engine is forced to work for wear. At the same time, the life of the device is significantly reduced, especially if family members actively use the stove.
In addition, the answer to the question is whether it is possible to put a refrigerator next to the gas stove in the kitchen, it will become obvious after the electricity accounts arrive. Having increased the intensity of its work 5-6 times, the refrigerator begins to consume much more electricity.
Unstable cooling negatively affects the microclimate in the unit chamber. The products placed on the shelves begins to be covered with thin ice crust. As a result, the food deteriorates or becomes tasteless. Especially actively, the formation of ice occurs in the freezer, so it will have to be defrosted more often than usual.
Electric stove and refrigerator
The owner of this kitchen insured and retreated at least 30 cm from the electric stove
Electric and induction plates heat the surface nearby than gas. Despite this, they should not be put close to the refrigerator. In addition to the load on the unit engine, you can encounter the following unpleasant moments:
- If the walls of the refrigerator case are not metal, yellow traces will appear in the places of contact with the stove;
- Rubber seal, the handles of the device and a plastic edging can crack or melt;
- Loading and unloading products is not as convenient as if the technique was shared by the table;
- The pens of dishes will rest against the wall of the unit or take a place in the aisle.
It should also be remembered that in some models the air grid is located on the side. It is on this part of the case that the main part of the heat accounts. This effect threatens the refrigerator breakdown.
If the refrigerator set next to the heating device will break during the warranty period, the repair service may refuse to freely maintain it, justifying its decision by a rude violation of the rules of operation of the equipment.
Increasingly, people began to use built.In household appliances and furniture. As a result, the kitchen becomes more cozy. The built.In oven has a design that allows you to put it at a convenient height. Protection from the effects of heat in such ovens is made more reliably. The refrigerator, built into the kitchen set, does not take up much space, fits perfectly into the interior of the kitchen. It provides for isolation, which blocks hot air entering the unit. The built.In refrigerator is fenced off with additional finishing panels. In this case, the smallest permissible distance between the refrigerator and the oven can be 15 cm.
Many have a microwave in the kitchen, the work of which does not affect the operation of the refrigerator at all. Its case is poorly heated due to short and infrequent use. It can be put on top of the refrigerator, but in the presence of recommended ventilation gaps. A heavy and large stove should be suspended on the wall, and with frequent use of the grill, you need to protect the upper surface of the device, putting on it a heat-insulating canvas or a sheet of a wood-fiber stove, wood-fiber planer or plywood.
The rational arrangement of household appliances provides comfort in the kitchen. In a spacious room, it is better to arrange equipment in different places. In other situations, build reliable fencing off.
Microwave on the refrigerator
In the operating instructions, manufacturers do not report whether it is possible to put the microwave on the refrigerator. However, the rules for installing any microwave oven say that the gaps around the body of the device are necessarily needed. After all, heated air should circulate freely through holes on one of the walls of the microwave.
- From the wall to the rear wall of the furnace, a distance of about 10 cm is required. By the way, this gap is also necessary for the correct operation of the refrigerator, because the air should also pass through its upper and back.
- Around the side walls you need gaps 5-10 cm.
- For the upper surface, a gap of about 20-30 cm is recommended.
Accurate recommendations should be sought in the instructions for the installation of your model of microwaves.
As for the harm of heat or microwaves, there is nothing to worry about here.
It turns out that if you put the microwave on the refrigerator with the recommended gaps for ventilation (for example, the furnace can be put on the legs), then there will be no problems. However, if the furnace is large and heavy, it is better to hang it on the wall (for example, using brackets), and if you often use the grill function, we recommend that you additionally protect the upper lid of the refrigerator using a heat-insulating canvas or plywood/wood-fiber slab/wood-and-wood Stricking plate.