How to set up a refrigerator stynol temperature mode

Table of Contents

What temperature should I set my refrigerator to?

Refrigerator Steinol how to adjust the temperature

The most important factor due to which the products in the refrigerator will maintain their properties for a long time, and it will serve you with faith and truth for more than a dozen years. This is the observance of the correct temperature regime in the refrigerator and freezer chamber. In order to set this mode, when the unit is commissioned, the temperature is adjusted in accordance with the instructions attached to the device. Consider the basic rules for adjusting the temperature in the refrigerator on the example of TM Steinol units.

Unlike the old Soviet devices equipped only by a switch operating in two positions (VCL/Off), modern refrigerators make it possible to adjust the temperature more easily and accurately. Dear models are even equipped with sensors that measure and highlight its value on the touch panel of the unit. How to set the temperature correctly, what value to focus on?

Some points you need to remember:

  • On average, the perfect temperature regime for the refrigerator is from 2 to 5 ° C. The more accurately the specified temperature is maintained, the longer the products will remain fresh and outwardly attractive. At a temperature higher than 5 ° C, the food begins to rot and mold, filling with bacteria and extraneous smells, therefore, when storing the products, this does not thus get food poisoning. If the regulator is turned all the way towards cooling and the temperature is set below 2 ° C, the food freezes and loses its useful qualities.
  • For products stored in the freezer, heat (plus temperature) is detrimental. After a few hours of stay in the conditions of improper temperature regime, meat and fish will simply spoil, since as a result of defrosting the quality of products worsens. That is why it is so important to set the temperature correctly.
  • Incorrect temperature adjustment leads to acceleration of ice melting and leakage, and also increases the cost of electricity. In addition, it is quite possible to expect the cost of repairs. Sensitive sensors of the thermostat with this mode of operation quickly fail.

Temperature adjustment in the refrigerator: how to configure the regulator

Today the refrigerator in most families is the main household device. Without its proper work, there will be neither delicious food nor family harmony.

One of the most important factors in this sense is a competently adjusted temperature. The more complex equipment, the more diverse the settings and the more likely to make a mistake.

How to avoid troubles and preserve the freshness and beneficial qualities of food in the refrigerator?

If the temperature in the refrigerator is set incorrectly

Most perishable products remain fresh at a temperature of 2 to 5. If the temperature controller in the refrigerator is twisted too much, the food freezes, losing useful properties.

After defrosting, it quickly becomes unusable. You have to cook in a hurry.

If the refrigerator is too warm, the active reproduction of bacteria begins in the products: fruits and vegetables rot, sausage and cheese are covered with mold, juices begin to roam.

High temperature is even more for frozen products. A faulty temperature sensor in the freezer in a few hours will turn fish or meat into a bad smelling mass.

We add to this the constant leakage of melted ice, as well as excessive energy consumption. And it will become clear why it is so important to correctly adjust the temperature in the refrigerator.

Unfortunately, not everything is even aware of what are the minimum and maximum working temperatures in their kitchen models. They will twist the pen. Does not intention on the walls, does not drip into the tray. And thank God.

Optimum temperature in the refrigerator

Since the refrigerator is usually a decent volume, heat is distributed unevenly through it. Much depends on where the compressor is located and how the refrigerator is structurally arranged.

In some models, the cold zone is closer to the upper part of the case, in others. In the middle part. The closer to the place of flow of cold air, the lower the temperature.

To decide how to properly distribute products on a refrigerator, let’s pay attention to the following facts:

At temperatures from 1 to 3, it is best to store meat, fish, chicken eggs, hard cheese, mayonnaise in open packaging.

At temperatures from 2 to 4, sausage and culinary products, soft cheeses are preserved longer.

At a temperature of 3 to 5, soups, boiled vegetables, dairy products, a loaf are stored.

For seafood, the most comfortable temperature is from 4 to 6 degrees. Fruits (with the exception of exotic. Bananas, pineapples, etc.D., which is generally undesirable to store in the refrigerator) should be placed in the warmest place of the refrigerator, where the thermometer shows 68 degrees.

refrigerator, stynol, temperature, mode

Based on this, you can approximately estimate how the grocery set is distributed according to your refrigerator model.

As for the freezer, do not forget: frozen products are equally stored as if.18 degrees, and with.25 ° C. Therefore, it is not necessary to chase the power of frost at all.

Adjustment of the refrigerator temperature

Oddly enough, most people do not even look into the instructions before the refrigerator in the network and the temperature adjustment is carried out by arbitrary rotation of the thermostat (in the case of electronic control of the temperature control of the LCD-display on expensive models, this procedure is still more correct).

At the same time, it is far from always possible to make an accurate and correct configuration. However, there are “folk” methods of control. Instead of trying to interpret arbitrary numbers on switches, it is better to check the air temperature with a street thermometer. Place it in a glass of water that put in the center of the refrigerator. Check the temperature in a few hours.

If it is higher than 4 degrees, feel free to twist the regulator towards cooling. If lower than 2-3 degrees, turn it in the opposite direction. As soon as you stabilized the temperature within 3-4 degrees, put the thermometer between the packages of frozen products in the freezer and wait a few hours.

At temperatures below.25 ° C, turn the temperature control controller if higher.18 ° C. Down to lower the temperature.

How to adjust the temperature in different brands of refrigerators?

In modern units, you can adjust the temperature of the freezer and refrigerating chambers separately, as well as different compartments independently of each other. We will analyze the features of thermoregulation in models of leading manufacturers represented in the domestic market:

  • Gorenje. The temperature in the refrigerator is set by turning the regulator handle to the position between Max and Min. It is recommended to install the thermostat in the ECO position. If the air temperature in the room where the refrigerator is installed below 16 degrees, the manufacturer advises to unscrew the handle on the Max, and with the surrounding heat. On the contrary.
  • Liebherr. Electronic temperature control, in many models. Separate regulation in the refrigerator and freezers. There is a CoolPlus mode. A system that protects the refrigerator from temperature changes in the external environment. As soon as the air in the room becomes colder, the compressor of the device begins to work with interruptions. Smartfreeze. A special cooling technology in which, due to active air circulation, it becomes possible to quickly freeze many kilograms of products at once. Superching modes and superbust frost in the freezer.
  • Atlant. The temperature is regulated by the rotation of the thermostat regulator in both directions. It has a dial on it. Adjustment occurs on a semibal scale: 0. The compressor is turned off, 1. The highest temperature, 7. The lowest.
  • Samsung. The temperature is adjustable using the control panel separately for freezing and refrigerating chambers:
See also  Cassettes for a refrigerator bag how to use

How to adjust the temperature in the refrigerator Stynol

CJSC “Stinol refrigerators”. A subsidiary of OJSC Novolipetsk Metallurgical Plant, is a universally recognized leader in the Russian market that produces household refrigerators of the European standard. The word “stinol” is formed from the elements of the phrase “steel from Novolipetsk”.

The production capacity of the plant built in 1990-93. Italian company Merloni Progetti. 1 million refrigerators per year. From the date of commissioning of the plant (July 2, 1993.) about 4 million refrigerators and freezers were produced. The share of the Stinol brand market in the domestic market in 1998. Reached 39.3%.

The plant produces refrigerators of large and small volumes with a static cooling system and with the No Frost system, with one and two compressors.

Household compression refrigerators “Stinol-101”, “Stinol-102”, “Stinol-103”, “Stinol-107”, “Stinol-123”, “Stinol-124” and “Stinol-104” are designed for short-term storage products and cooling of drinks in the refrigerator (HC), as well as for long.Term storage of food and cooking of food ice in the freezer (MK). The refrigerant is the R134A.

The device of the refrigerator-mod

The refrigerator is a floor cabinet made of rectangular panels (rice. 1, a), which, in turn, consists of an external and internal cabinets. The outer cabinet is metal, and the internal is made of shock.Resistant polystyrene; The space between them is filled with thermal insulation. As thermal insulation, polyurethane foam (PPU) is used, which rigidly connects the external and internal cabinets, turning them into a non-vegetable monoblock.

Rice. One.STINOL-103 Moroster refrigerator KSHMH 340/200:

A. General view: b-scheme of the refrigerators of refrigerators of refrigerators-models “STINOL-103” and “STINOL-102”:
1. Adjustable supports; 1. Compressor;
2. Base; 2. Absorption tube;
3. Department for storing frozen products; 3. Capillary tube;
4. Department for freezing products; 4. Evaporator of the refrigerator;
5. Guides for water drain; 5. Evaporator of the freezer;
6. Control panel; 6. Capacitor;
7. Fastening of the capillary tube of the thermostat; 7-filter-dryer;
8. Lighting unit; 8. Uplifting tube
9. The door of the refrigerator;
10. The door of the freezer;

The front opening of the cabinets is closed by two doors. The space between the internal panels of the doors and the metal case is also filled with polyurethane thermal insulation, and therefore separate replacement of individual elements of the doors is impossible.

The STINOL-103 Moroster refrigerator has two refrigeration units (rice. 1, b) serving the refrigerator and freezers individually.

The evaporator of one of the units, cooling the refrigerator (HC), is fixed and filled with foamed PPUs between the back walls of the internal and outdoor cabinets, evaporator 1 (rice.

2) another unit, cooling the freezer (MK), is a steel galvanized tube mounted on steel plates, which serve as regiments of the freezer. If necessary, the entire MK evaporator can be removed and replaced.

Rice. 2.Closure of the refrigerator “STINOL-103” KSHMH 340/200:

refrigerator, stynol, temperature, mode
1. Evaporator of the freezer; 11. Electropatron: 22. Door;
2. Return tube; 12. The case of the door switch; 23. Plastic flags;
3. Pipe clamp; 13. Lattices; 24. Regiment;
4. Guide evaporator; 14. Bar; 25. Lower box
5. Coupling; 15. Switch;
6. Ice bath; 16. Lighting unit;
7. Sleeve; 18. Traffic jam;
8, 17. Homing screws; 19. Pallet;
9. Ceiling; 20. Upper box;
10. Lamp; 21. Guide doors;

The evaporator of the refrigerator chamber is non-removable and made of a copper tube, so its failure due to corrosion is unlikely. Compressors of refrigerators 9, 16 are located on a metal traverse 12, in the machine department in the rear of the cabinet. The capacitor 5 is fixed on the rear wall of the cabinet, part of the tubes of which is included in the system of one refrigeration unit, and part into the system of the other.

Rice. 3.The condenser and compressor of the refrigerator “STINOL-103” KSHMH 340/200:

1, 2, 4, 7, 11, 13, 18, 21. Self.Supporting screws; 12. Metal traverse:
3. The upper cover of the refrigerator; 14. Shock absorber;
5. Capacitor; 15. Guide panel;
6-filter-dryer; 17. Gaskets;
8. Bath for taking melt water; 19. Prefabricated clamping box;
9, 16. Compressors; 20. Cord;
10. Sleeve; 22. Pipe for draining melt water

The role of the throttle device is played by a capillary tube with an internal diameter of 0.71 mm in the refrigerator unit of the refrigerator and an inner diameter of 0.66 mm in the unit of the freezer. The outer diameter of both tubes is 1.95 mm. The presence of such an element in the refrigerator makes it sensitive to moisture and other pollutions that have fallen into its internal system. In this regard, special attention is required to the cleanliness and dehydration of the refrigerators system.

Instructions for two.Chamber refrigerators Stinol

How to adjust the temperature in a two.Chamber refrigerator Steinol 101

Steinol 101 refrigerator. A two.Chamber device that consists of a refrigerator and freezer compartments. The control of the unit is carried out due to the electromechanical method of regulation. The model has one compressor and two independent evaporators that provide air cooling to the required level in both departments.

The average temperature of the refrigerator is 5 ° C, the freezer is not higher.18 ° C. Maintaining the temperature at a given level. A consequence of the periodic turning on and off the compressor using a thermostat and a launcher relay.

The reinforcing compartment of the device is carried out automatically before the next inclusion of the compressor. The accumulation of melt water occurs in a special container on the compressor, after which it is evaporated.

Thauing the freezer should be carried out in manual mode when a layer of hoarfront is over 5 mm.

How to adjust the temperature in a two.Chamber refrigerator Stinol 103 (RF S 345)

Two.Chamber refrigerator Stinol 103 with the lower arrangement of the freezer is equipped with two compressors and two evaporators with a sequential connection. This provides autonomous operation of the refrigerator and freezer compartments with the possibility of autonomous temperature adjustment and turning off one of the cameras using controllers on the control panel.

Defrosting the refrigerator compartment is carried out automatically by the drip method. The freezer department must be defrosted manually.

How to adjust the temperature in a two.Chamber refrigerator Steinol 104

Stynol-104 Moroziner is three-chamber and consists of refrigerated, freezer and retractable (for storing vegetables and fruits) chambers. Freezer, located at the top of the refrigerator, equipped with a “no frost” system with cold air circulation and automatic thawing of the evaporator. The timer periodically turns off the compressor, and the fan, and turns on the heating elements of the evaporator and the pallet of the freezer. During the melting of a layer of hoarfrost on the evaporator, the water flows onto a heated pallet and falls on the channels on a tray for collecting melt water, where it evaporates. Thermoregulator is located on the top control panel. Turning the handle of the thermostat clockwise increases the mode of operation of the refrigerator. We recommend installing a thermostat in the middle position.

See also  Automatic fan speed adjustment from temperature

How to adjust the temperature in a two.Chamber refrigerator Steinol 107

Stinol 107 device is a two.Chamber refrigerator equipped with one compressor. The cooling of the freezer compartment is carried out due to the functioning of the evaporator of the Knou Frost and fan system. The refrigerator compartment is cooled thanks to an autonomous evaporator located on the outer surface of the posterior wall.

The minimum temperature supported by the freezer is.18 degrees Celsius. The additional capabilities include the supermarket function.

How to adjust the temperature in a two.Chamber refrigerator Steinol NF 330 4T

STINOL NF 330 4T. Representative of three.Chamber refrigerators with one compressor. Equipped with four temperature zones, the thawing of which is automatically. The temperature regime of each compartment is adjusted autonomously, which allows you to set the optimum temperature for storing various products.

The freezer maintains the temperature to.18 degrees Celsius. A mode of 8 to 14 degrees is installed in a retractable container for vegetables.

How to adjust the temperature in a two.Chamber refrigerator Steinol 110

Adjusting lambs with risk for both camera has the same number of working positions. 5 of them. But thermostats for the refrigerator and freezer use different. The No Frost system is installed in the freezer, the thermostat has a diagram with a cyclic inclusion of a dry ice recovery system.

STINOL refrigerator instructions include a section in which there are instructions on how to adjust the temperature. Both cameras have a control and risk handle for turning. The number 1 corresponds to the highest temperature in the regulation range, the number 5 is low. The position is indicated on the pad.

Initially, indicators are exhibited in the middle part of the scale, even before the device is turned on. According to the instructions, the cold should get in the cells in 4 hours, and only then you can place products there.

It is necessary to adjust the handle gradually, turning 1 risk after 5-6 hours with temperature measurement inside the chamber. If the device does not respond to commands, it is necessary to determine if the thermostat works.

How to adjust the temperature in a two.Chamber refrigerator Steinol 110l

Cutting. Two sticks and one stick. One is the “arrow of the bow”. Two sticks are arrow plumage.

The minimum temperature is to twist counterclockwise to a lot of emphasis (“one stick”), a little stronger and the refrigerator will turn off. It is normally considered invention.

The closer to mines., the less the compressor works, which means less energy consumption.

But! Too at least and temperature may not be enough, it will begin to “sour food”. So install it.

Middle, a day or two smaller. Suits the temperature, in a day. Two are still a little less. It became a warm in the cell, return a little back.

How to adjust the temperature in a two.Chamber refrigerator stynol with a drop system

Adjustment of equipment with a drip system is carried out after installation in the room. For stable air circulation, it is necessary to leave a small space between the sidewalls of the equipment and the rear block of the case. The parameters of the intervals are indicated in the technical documentation.

The work is carried out in the following sequence:

refrigerator, stynol, temperature, mode
  • Stinol refrigerator needs to be left in the room for 3-4 hours. Then the device is connected to the household electrical network.
  • Setting is performed in standard models using a thermometer.
  • The thermometer must be placed inside the refrigerator compartment, the temperature corrector is placed in the middle position.
  • After the operation of the equipment for 2-3 hours, the parameters of the thermometer must be checked.
  • With a thermometer 2 5 ° C, the equipment is considered correctly configured.
  • At the next stage, the freezer is checked, it is necessary to set the temperature at least.18.21 ° C.

Adjust the temperature in different compartments of the refrigerator

There is no single standard, there may be minor differences depending on the design features of the device. An important role is played by the distance between the main storage area of ​​food and the freezer. Therefore, consider the average values.

Branch to preserve freshness of products

For this compartment it is necessary to set a temperature of 0/1 ° C. The department in question is best suited for storing fish and meat products. Weak cooling prevents food damage, but at the same time remain: taste properties, nutritional value, freshness and even the appearance of products.

The temperature setting is important, but you should not neglect other rules for storing food. Previously, the product must be wrapped in a film or put in a special container. Fresh compartment is designed for storage:

The optimal indicator for the next zone will be 2-4 degrees. This is a suitable place for storing meat blanks that you plan to cook in the near future. In the refrigerators Atlant there is a special egg tray. In order to maintain the desired temperature:

Do not oversaturate the refrigerator with products and dishes with finished food.

Compliance with these simple recommendations will avoid additional embezzlement for repairing refrigerators in Kyiv, which will be required in case of breakdown of one of the hardware modules.

Refrigerator Troubleshooting. How-To-Video. Incorrect Temperature

Middle shelves

The optimum temperature for this compartment is from 3 to 6 degrees. Medium shelves are designed to store cooked dishes: cereals, sauces, soups, etc.D. Often the shelves are made of glass, plastic, metal.

Containers for fruits and vegetables

They are located at the bottom of the structure of the unit. Therefore, the operating temperature reaches 8 degrees. Remember that while loading the refrigerator, you need to properly distribute products by zones, adhering to the basics of the commodity neighborhood. Unsuitable storage conditions will become a catalyst for premature damage to food.

Door shelves

This is the warmest compartment of the refrigerator. Averaged temperature range. From 5 to 10 degrees. Regular opening of the door causes the transition from the cold environment to warm. Therefore, placing perishable products, for example, milk or eggs, is not worth it here. The best option is sauces, oils, seasonings.

Freezer

The temperature control in this compartment is often set at the level.18 degrees. Activation of the “Super.Summary” mode will lead to the fact that the temperature will drop to.30 degrees. Such conditions are suitable for instant freezing. In the freezer, products are stored much longer. However, this does not mean that they should lie for more than a month. Over time, any food loses nutritional value, taste.

The temperature monitoring is extremely important. Timely adjustment allows you to maintain freshness of food. On the control panel is a special regulator designed to control the temperature regime.

The device of the electric system

Normal operation of any compressor refrigerator is provided by the electrical circuit.

In the simplest form, it includes several elements:

  • Thermoregulator responsible for maintaining a certain temperature.
  • Thermal protection relay preventing compressor overheating.
  • Electric motor.
  • Launch relay responsible for starting the motor.

The working cycle is as follows. When the voltage is supplied to the device, the current moves through the thermostat with closed contacts, the forced thawing button, then through the thermal protection relay on the starting relay and on the work winding of the motor.

See also  Gorenje refrigerator does not cool the upper chamber

Since the motor shaft stands, the current flowing along its working winding has a value much higher than the nominal. This is necessary, since the design of the starting relay provides for the closure of contacts on the launch winding only when the nominal current exceeds. Thus, the relay transfers the current to the launch winding, the engine begins its rotation, the voltage in the working winding disappears.

The motor continues to work in normal mode, the refrigerator starts freezing. At the time of the previously given temperature, the thermostat is triggered.

He opens his contacts, and the current ceases to go to the engine. The compressor of the refrigerator stops. When the temperature changes, the contacts of the thermostat are closed again and the cycle is repeated.

To protect against dangerous for the overheating motor, thermal protection relay is provided. Its main element is a flexible bimetallic plate. Upon achieving a dangerous temperature, it begins and opens the contacts, the cooled element “rises” in place and closes them.

The principle of operation of the refrigerator

All refrigerator equipment work on a similar principle, performing two main tasks: the concentration of cold in the inside of the device and the removal of the resulting thermal energy outside. In modern equipment, Freon is most often used. A popular type of refrigerant.

Freon includes fluorine, chlorine and ethane. This refrigerant has a unique quality: to move from a liquid state to a gaseous one when the pressure fluctuations inside the system. The cooling procedure looks as follows.

  • The compressor tightens the refrigerant inside.
  • The piston pushes him through the tubes.
  • In the process of heat transfer, the refrigerant begins to condensate.
  • Freon becomes liquid.
  • Moisture is absorbed by a sorbent, turning into gas.
  • Further, the refrigerant enters the capillary pipe.
  • Pressure drops along with the gas temperature.
  • Passing through the evaporator, Freon changes its properties.
  • The refrigerant in the gas state again enters the compressor.

On sale you can find models with two compressors. One for the main camera, the other for the freezer. On the one hand, the effectiveness and quality of cooling increases markedly, but on the other hand, the maintenance and repair of equipment is complicated. The refrigerator can also be equipped with a drop system or nofrost technology.

Compression models are the most common solutions in the refrigerator market. Here the movement of Freon is organized due to the change in pressure. But there are other types of refrigerator systems:

In the adsorption technique as a refrigerant, ammonia is used. Clear disadvantages of such devices are problematic maintenance and unsafe substance. Systems of such a plan were used in old technology, which has already been discontinued from production.

In vapor.Ejector refrigerators, water runs through the tubes, and the role of the pump is played by the ejector. The system is stable, safety and environmental friendliness, but it consumes a lot of electricity and fluids to pump temperature.

Thermoelectric models work according to the principle of the Dumpete effect: heat absorption through two conductors and current. The system is reliable, durable, but it is very expensive, just like its maintenance.

A small plate informs about the following:

  • Full name of the refrigerator.
  • Serial factory room.
  • The country where the refrigerator was produced.
  • Class of climatic affiliation.
  • On energy conservation and electricity consumption.
  • The volume of each chamber separately and the total volume of the device.
  • About the amount of kilograms of products that the refrigerator is able to freeze.
  • Release date of this model.

Plus, the technical passport of the Biryusa refrigerator, Persis, Indesite, Samsung contains information about the materials that were used for the production of this model. As well as a number of information details that are necessary for maintenance.

Rules for adjusting temperature in the refrigerator Stynol

The most important factor due to which the products in the refrigerator will maintain their properties for a long time, and it will serve you with faith and truth for more than a dozen years. This is the observance of the correct temperature regime in the refrigerator and freezer chamber.

In order to set this mode, when the unit is commissioned, the temperature is adjusted in accordance with the instructions attached to the device. Consider the basic rules for adjusting the temperature in the refrigerator on the example of TM Steinol units.

General temperature rules for the refrigerator

Unlike the old Soviet devices equipped only by a switch operating in two positions (VCL/Off), modern refrigerators make it possible to adjust the temperature more easily and accurately. Dear models are even equipped with sensors that measure and highlight its value on the touch panel of the unit. How to set the temperature correctly, what value to focus on?

Some points you need to remember:

  • On average, the perfect temperature regime for the refrigerator is from 2 to 5 ° C. The more accurately the specified temperature is maintained, the longer the products will remain fresh and outwardly attractive. At a temperature higher than 5 ° C, the food begins to rot and mold, filling with bacteria and extraneous smells, therefore, when storing the products, this does not thus get food poisoning. If the regulator is turned all the way towards cooling and the temperature is set below 2 ° C, the food freezes and loses its useful qualities.
  • For products stored in the freezer, heat (plus temperature) is detrimental. After a few hours of stay in the conditions of improper temperature regime, meat and fish will simply spoil, since as a result of defrosting the quality of products worsens. That is why it is so important to set the temperature correctly.
  • Incorrect temperature adjustment leads to acceleration of ice melting and leakage, and also increases the cost of electricity. In addition, it is quite possible to expect the cost of repairs. Sensitive sensors of the thermostat with this mode of operation quickly fail.

Temperature norms for the refrigerator for various products

The stinol refrigerator temperature controller must be fixed in a position that, according to the instructions, is most consistent with the perfect temperature regime. After that, the products on the shelves are placed in accordance with the storage standards established for them and the cold distribution system by the chamber (some models have the coldest shelf of the upper one, and some have average).

So, what is the temperature in the refrigerator Stinol will be optimal for the different food stored in it:

  • Dishes of meat and fish, as well as eggs, hard cheeses, milk and dairy products, sauces are best preserved at a temperature of 1 to 3 ° C, therefore they are located on the colder shelf.
  • In the range from 2 to 4 ° C, sausage, Brynza, ready.Made dishes from cereals and semi.Finished products feel great.
  • Soups, boiled vegetables and a loaf remain long as fresh, if stored at a temperature of 3 to 5 ° C. This is the middle shelf.
  • The installed temperature rate for seafood is from 4 to 6 ° C, therefore, this should be the temperature on the shelf where they lie.
  • Fresh vegetables and fruits are placed on the lower shelf or in a special compartment, where the temperature ranges from 6 to 8 ° C (the exception is only pineapple and banana. It is better to keep them outside the refrigerator at room temperature).

In frozen form, any product will be stored for a fairly long period.

| Denial of responsibility | Contacts |RSS