Does not cold the top of the refrigerator hotpoint

Does not cold the top of the refrigerator hotpoint

The following reasons that occur in the case when the freezer freezer works, and the refrigerator does not cold, are indicated from the most probable to the least probable. Check or test each reason, starting with the most likely reasons. Reason 1 Frozen the evaporator coils

does, cold, refrigerator, hotpoint

The heating device of the sealing is turned on several times during the day to melt any frustration that can be accumulated on the evaporator coils. If the thawing heater block is defective, then the frost will continue to accumulate on the reels of the evaporator and forget the coils. If the evaporative coils freeze, then this will limit the flow of air passing through them, as a result of which the refrigerator does not cool. Check the evaporator coils to determine the presence of frosts on them. If the evaporator coils are frozen, then check each component of the defrosting system.

Reason 2 of the evaporator fan engine

The evaporator fan engine supplies cold air through the evaporator coils and circulates throughout the freezer. If the evaporator fan does not work, then the freezer or refrigerator will not work normally. To determine whether the evaporator fan engine is defective, try to handle the fan blad manually. If the fan blad does not rotate freely, then replace the fan engine. In addition, if the engine is too noisy, then replace it. Finally, if the engine does not work at all, then use a multimeter to check the engine winding for continuity. If the continuity of the winding is broken, then replace the evaporator fan engine. Reason 3 Dampfer control unit

The control of the air damper (dampfer) is opened and closed to ensure a sufficient amount of cold air in the refrigerator compartment. If the damper does not open properly, then it will not let cold air into the refrigerator. Check the control of the air damper (damper) to determine if it is broken or closed and not surrounded.

Thermistor controls the temperature of the refrigerator and sends the temperature indications to the control board. Then the control board regulates the power of the compressor and fan of the evaporator based on the readings of the termistor. If the termistor is faulty, then the compressor and evaporator fan may not work if necessary or can work too often. To determine whether the termistor is faulty, check it using a multimeter. The resistance of the termistor should vary depending on the temperature of the refrigerator. If the resistance of the termistor does not change or the continuity of the thermistor is broken, then replace it.

Reason 5 temperature control board

The temperature control board regulates the current supply for compressor and fan engines. If the control board is faulty, then it may stop supplying voltage to the compressor or fan engines. Control panels are often erroneously diagnosed. Therefore, before replacing the control board, first check all the other more often broken components. If none of the other components is broken, then think about replacing the temperature control board.

Reason 6 Thawing Management Plant

The defrosting control board (thawing) determines how often to start the defrosting cycle. If the thawing control board does not work, then the refrigerator will not run the defrosting cycle, and the frost will continue to accumulate on the heels of the evaporator. If the evaporative coils freeze, then the refrigerator will work more intensively to cool. As a result, the refrigerator can be too warm. If the thermostat is shared and the thawing heater operates correctly, then most likely, the reckoning control board is faulty and it will need to be replaced.

Reason 7 Timer Tight

The latrice timer includes a defrosting heater several times during the day to melt any frost.Free that can accumulate on the evaporator coils. If the defrosting timer is faulty, then it may not go into the cycle of hidden, or will not give a current to the heating heater during the defrosting cycle. If the defrosting system does not work, then the frost will continue to accumulate on the heels of the evaporator, and the refrigerator will have to work more for cooling. As a result, the refrigerator can be too warm. To determine whether the thawing timer is faulty, slowly switch the toggle switch to the defrosting cycle. The compressor should turn off, and the heater must turn on. If the timer does not supply power to the components of defrosting or does not leave the defrosting cycle for 30 minutes, then this means that the timer is not working and requires replacement.

Reason 8 Thermostat of Defrosting

The thermostat of defrosting controls the temperature of the evaporator coils. Когда катушки охлаждаются ниже заданной температуры, термостат срабатывает, чтобы обеспечить подачу питания на нагреватель оттайки во время цикла размораживания. In the defrosting cycle, the thawing heater melts any frost.Free, which can accumulate on the reels of the evaporator. If the thermostat of defrosting is defective, then it will not work, as a result of which the current will not get to the heating heater. To determine whether the thermostat is defective, use the multimeter to check it for continuity. If the continuity of the thermostat of defrosting is violated when the low temperature of the working range is reached, then replace it. Reason 9 Main control

See also  Food without a refrigerator what to take

Perhaps the main management fee is faulty, but this is rarely the cause of the problem. Before replacing the control fee, first check more and more broken components. If none of these components is broken, then consider the possibility of replacing the main control board.

Important: myths and fairy tales

There are many articles on the Internet in which incompetent people advise. The reasons why the main compartment of the refrigerator does not work, they can call the following:

  • The doors close the doors;
  • The seal was worn out;
  • Too hot in the apartment;
  • Often use the main compartment;
  • Put the hot in the refrigerator.

Indeed, all this leads to improper operation of the equipment. But so that the main camera does not work There must be a good reason. And not that you quickly closed the door or put a pan with a warm soup in the refrigerator. And now more.

Problems with doors and seals

Suppose a gap between the door (seal) and the refrigerator body will be 1 cm. Then the main camera will cool, but the compressor will have to be tight. It will often turn on, or constantly work. But the refrigerator will maintain the temperature.

How to fix your Hotpoint fridge leaking water underneath

High temperature in the apartment

There is an opinion that in the heat the refrigerator does not cope with the work. In fact, manufacturers make equipment with a power supply. Even if you have 35 in your apartment, the refrigerator will work. Expending to electricity is possible, but he will cope with his task.

Frequent use

Any manufacturer of refrigerators counts on the opening and closing of the wings. This is the normal functioning of such a technique. Yes, the more often you open the main camera of the refrigerator, the greater the flow of heat. But this will only lead to the following:

Hot food in the refrigerator

Indeed, when you put hot dishes in the refrigerator, the load on the compressor increases. He will not always cope with her. The camera can warm up and it seems that the refrigerator does not cold. But this is temporarily, soon the compartment will cool to the optimum temperature.

Does not cold the top of the refrigerator hotpoint

The following reasons that occur in the case when the freezer freezer works, and the refrigerator does not cold, are indicated from the most probable to the least probable. Check or test each reason, starting with the most likely reasons. Reason 1 Frozen the evaporator coils

The heating device of the sealing is turned on several times during the day to melt any frustration that can be accumulated on the evaporator coils. If the thawing heater block is defective, then the frost will continue to accumulate on the reels of the evaporator and forget the coils. If the evaporative coils freeze, then this will limit the flow of air passing through them, as a result of which the refrigerator does not cool. Check the evaporator coils to determine the presence of frosts on them. If the evaporator coils are frozen, then check each component of the defrosting system.

Reason 2 of the evaporator fan engine

The evaporator fan engine supplies cold air through the evaporator coils and circulates throughout the freezer. If the evaporator fan does not work, then the freezer or refrigerator will not work normally. To determine whether the evaporator fan engine is defective, try to handle the fan blad manually. If the fan blad does not rotate freely, then replace the fan engine. In addition, if the engine is too noisy, then replace it. Finally, if the engine does not work at all, then use a multimeter to check the engine winding for continuity. If the continuity of the winding is broken, then replace the evaporator fan engine. Reason 3 Dampfer control unit

The control of the air damper (dampfer) is opened and closed to ensure a sufficient amount of cold air in the refrigerator compartment. If the damper does not open properly, then it will not let cold air into the refrigerator. Check the control of the air damper (damper) to determine if it is broken or closed and not surrounded.

Thermistor controls the temperature of the refrigerator and sends the temperature indications to the control board. Then the control board regulates the power of the compressor and fan of the evaporator based on the readings of the termistor. If the termistor is faulty, then the compressor and evaporator fan may not work if necessary or can work too often. To determine whether the termistor is faulty, check it using a multimeter. The resistance of the termistor should vary depending on the temperature of the refrigerator. If the resistance of the termistor does not change or the continuity of the thermistor is broken, then replace it.

Reason 5 temperature control board

The temperature control board regulates the current supply for compressor and fan engines. If the control board is faulty, then it may stop supplying voltage to the compressor or fan engines. Control panels are often erroneously diagnosed. Therefore, before replacing the control board, first check all the other more often broken components. If none of the other components is broken, then think about replacing the temperature control board.

Reason 6 Thawing Management Plant

The defrosting control board (thawing) determines how often to start the defrosting cycle. If the thawing control board does not work, then the refrigerator will not run the defrosting cycle, and the frost will continue to accumulate on the heels of the evaporator. If the evaporative coils freeze, then the refrigerator will work more intensively to cool. As a result, the refrigerator can be too warm. If the thermostat is shared and the thawing heater operates correctly, then most likely, the reckoning control board is faulty and it will need to be replaced.

See also  How long will the refrigerator withstand without electricity

Reason 7 Timer Tight

The latrice timer includes a defrosting heater several times during the day to melt any frost.Free that can accumulate on the evaporator coils. If the defrosting timer is faulty, then it may not go into the cycle of hidden, or will not give a current to the heating heater during the defrosting cycle. If the defrosting system does not work, then the frost will continue to accumulate on the heels of the evaporator, and the refrigerator will have to work more for cooling. As a result, the refrigerator can be too warm. To determine whether the thawing timer is faulty, slowly switch the toggle switch to the defrosting cycle. The compressor should turn off, and the heater must turn on. If the timer does not supply power to the components of defrosting or does not leave the defrosting cycle for 30 minutes, then this means that the timer is not working and requires replacement.

Reason 8 Thermostat of Defrosting

The thermostat of defrosting controls the temperature of the evaporator coils. Когда катушки охлаждаются ниже заданной температуры, термостат срабатывает, чтобы обеспечить подачу питания на нагреватель оттайки во время цикла размораживания. In the defrosting cycle, the thawing heater melts any frost.Free, which can accumulate on the reels of the evaporator. If the thermostat of defrosting is defective, then it will not work, as a result of which the current will not get to the heating heater. To determine whether the thermostat is defective, use the multimeter to check it for continuity. If the continuity of the thermostat of defrosting is violated when the low temperature of the working range is reached, then replace it. Reason 9 Main control

Perhaps the main management fee is faulty, but this is rarely the cause of the problem. Before replacing the control fee, first check more and more broken components. If none of these components is broken, then consider the possibility of replacing the main control board.

The refrigerator makes a crack

Clicks and other sounds inside the refrigerator are not always indicated about its malfunction. If there are no problems with cooling products, then this is due to the following processes.

  • When the device engine is turned off, the crack can come from the material of the internal walls, which is deformed when temperature drops.
  • If the sound is heard from the newly purchased refrigerator, this may be due to the operation of the thermostat when starting the motor.

However, if the noise is not published for any of these reasons, then, most likely, the fault of this breakdown. Consider the following options.

    If the refrigerator model is electromechanical, then the problem can be in the thermostat. It controls the temperature in the device chamber, and when it rises to a certain level, it gives the signal of the board to launch the motor. If it does not work, then the thermostat will constantly click, and the refrigerator will not turn on.

Replacing the thermostat in the refrigerator Indesite

Excessive ice formation

Modern models require periodic defrosting. At least every six months. Then there is more likelihood that such problems will not appear at all

Unusual design, the amount of snow is often formed in models that support No Frost technology. The effect appears due to the fact that the evaporator is faulty in the freezer. For this reason, the thawing function ceases to hard. Inside the temperature becomes higher. The motor works without interruptions, which leads to the formation of ice. Another problem is when the refrigerator does not freeze.

Possible refrigerator malfunctions

If the refrigerator stopped cooling, and the freezer is covered with ice, then you should immediately contact professionals. Idleness will entail different consequences. So, the products will quickly deteriorate, and the equipment will completely stop functioning over time.

The common reasons that the refrigerator stopped freezing is attributed:

  • Relay malfunction;
  • Damage to the start.Up capacitor;
  • Combustion of the motor;
  • Freon leak (the technique works, but cooling does not start);
  • Enforcing the capillaries system by which the refrigerant is supplied.

Before contacting the service center, you need to check if there is a gap between the door and the seal. Through it, warm air can come through it, which will harm not only products, but also technology itself. As a result, such a common problem arises as the refrigerator began to freely freeze.

The flow of air into the chamber is possible for the following reasons:

  • The technique stands on an uneven surface, which leads to overhabiting of the doors;
  • Installation of heavy objects on the door drive to sagging;
  • In the old models there is no “open door” signal, which often causes a random formation of a gap (it should not be wondered why the freezer is covered with ice);
  • The formation of ice, which prevents the hermetic closure of the door;
  • Damage to the seal or loss of elasticity.

If the check showed the serviceability and density of the door, it is worth considering other reasons why the refrigerator works, but does not freeze.

Freon leak

If the compressor is constantly working without disconnecting, and the refrigerator cools poorly, then the cooling circuit is possible. Gradually, the temperature in the internal space rises. If the circuit is damaged, a gap is formed through which Freon flows from the system.

See also  Gorenje refrigerator does not cool the upper chamber

Establish the reasons why the refrigerator does not freeze, you can independently. To do this, just check the condition of the capacitor with your hand. If the grill is hot, then the device works fine. If the circuit is damaged, the capacitor is cold, which indicates the leakage of the freon.

To eliminate the problem why the refrigerator does not cold, it is necessary to carefully check the system and detect damage. The gap is blocked and a new refrigerant is filled. It is recommended to refuel the Freon of the same brand as before. Otherwise, the equipment may begin to work incorrectly. Often this becomes the reason that the refrigerator is poorly freezing.

Reducing the cooling system

In the process of using household appliances, the relief of the capillary tube and the filter-dryer is often observed. The main cause of blockage is the use of poor.Quality freon, which contains a large amount of moisture. This is observed with the wrong refueling. The process is carried out only if preliminary vacuuming.

Without this, the refrigerant will begin to evaporate. Evaporation is accompanied by the formation of water, which further freezes and forms a cork. This reason leads to the fact that the refrigerator does not work or the refrigerator is poorly freezing.

As for the filters, they are designed to prevent moisture from entering the system. With the wear of the drainage, the probability of ice blocking arises. The reason for the stopping may be solid particles. These can be the products of compressor wear and other system elements. This explains why the refrigerator does not cold.

Hotpoint RFA52 Fridge Freezer Won’t cool down, temperamental problem, fridge thermostat replacement

When stopping the cooling system, the refrigerator is buzzing, but does not cold. The reason for this uncharacteristic noise is that the engine is forced to work under a large load. He is forced to push Freon, despite the educated blockage. To eliminate the malfunction, it is necessary to call professionals. Using special hydraulic equipment, the system is cleaned. The clogged tubes are blown, and a worn filter-dryer is replaced.

Compressor malfunction

If the compressor is hot, this does not mean that it works correctly. In some cases, it may not turn on. But sometimes the unit works periodically. At the same time, its inclusion is accompanied by roar, strong noise and clicking. All this indicates the wear of the unit. He is not able to work normally and ensure the normal pressure of the freon on the network.

In the presence of such signs, it is worth diagnosing the compressor of the refrigerator. First check the contacts. If the compressor does not work, then it is changed. With minor problems, repair is carried out.

Malfunction of the control unit and other nodes

The malfunction of the thermostat, thermal attemptor and control unit leads to the fact that the compressor does not accept the correct information about the state of temperature in the chambers. This does not make it possible to start regulation of the regime. The malfunction of the analyzing elements leads to the fact that the compressor of the refrigerator is completely or partially not working.

Professionals do not exclude such probability. Therefore, in diagnosis, they check the serviceability of all sensors and regulators. Faulty elements are replaced. Especially if the refrigerator does not freeze, and the freezer works.

Disconnecting the refrigerator

The cause often becomes a relay that protects or disconnects the mechanism. The problem can be more serious, associated with the fact that the compressor has come out of the system. There are common cases when the winding simply burns. Then the compressor all the time is hot, and traffic jams are knocked out in the apartment, the refrigerator Ariston Hotpoint stops working correctly.

The temperature sensor can also become a detail due to which the launch of the equipment becomes problematic. In turn, the design is out of order if a chain with a motor is torn. Then the switching signal does not reach where you need. Hotpoint Ariston does not freeze.

Similar questions

Hotpoint Ariston refrigerator does not burn display more than a year ago HotPoint-Ariston Ebyh 18213 O3 F refrigerators

Our worker has a hotpoin-ariston refrigerator, unexpectedly, stopped burning the display, whether it could be corrected and if possible, then for.

Our refrigerator has a hotpoin-ariston does not freeze the upper chamber, what is the possible problem?

Hot Point Ariston Refrigerator does not turn off more than a year ago HotPoint-Ariston HTM 1181 refrigerators.2

We have a refrigerator Hotpont Ariston generally stopped turning off and works all the time, which could fail and how much it will be.

Water accumulation at the bottom of the refrigerator

In this situation, it is necessary to check how the products are located in the refrigerator, and sort them out. It is likely that they are closely pressed against the wall of the chamber and do not allow condensate to drain down. Also, water cannot go into the drainage hole due to the fact that it is clogged with husk, particles of food and crumbs. You can clean it yourself.

Read: How to clean a drainage hole.

Cleaning the drainage opening is necessary in refrigerators with a drop system of defrosting

| Denial of responsibility | Contacts |RSS