Arderia boiler does not turn on the control panel

arderia, boiler, does, turn, control, panel

Malfunctions of the arderia gas boiler. Error codes, causes and methods of elimination

Refusal to use by centralized heating and water supply lines, the creation of autonomous heating systems and the supply of hydroelectric power plants at home becomes commonplace.

This is convenient for owners of private houses or apartments, allows you to independently make decisions about the beginning and end of the heating season or the modes of heating of housing.

Tint networks offer a wide range of gas boilers, on the basis of which the most effective and economical heating systems are created.

Arderia ошибка A5

European companies are considered confident leaders in the production of heating equipment, but their colleagues from Southeast Asia have achieved considerable successes.

Consider bright representatives of heating equipment from South Korea. Gas boilers Arderia (Arderia).

Errors of gas boilers Arderia and methods for their elimination

Any gas boiler needs regular care and preventive measures. It happens that external factors become the causes of malfunctions: low pressure in the highway, tension changes, etc.

The malfunctions of gas double.Circuit wall boilers Arderia are detected in the form of codes on the screen. Their decryption is in the operating instructions.

Perhaps at the end of the coaxial pipe there was an ice that prevents the exit of it from it

Perhaps all shut.Off valves of the heating system are closed

Check the operability of the three.Way valve and the sensor of the hydraulic duct.

The speed speed of the circulation pump should be adjusted.

  • Weak gas pressure;
  • Malfunctions in the operation of a gas valve or transformer;
  • Blocking the gas transmit
  • Cut valves are closed;
  • Filters clogged;
  • There were problems in the circulation pump or three.Way valve.

Check the performance of the pump and three.Way valve

Models of gas boilers Arderia B10, B14, B16 have other errors codes. Consider what they mean and how to eliminate the malfunctions.

E0. Anti.Frustration mode. This code is displayed on the screen if the temperature of the coolant dropped below 1 ° C. It is necessary to check the integrity of the system in which the liquid circulates. The error disappears if the coolant is heated. If it has not disappeared, call the master.

The gas boiler does not gain temperature. The causes and methods of their elimination

Find out here why the gas boiler does not light up?

Why the gas boiler works without stopping. The reasons and methods of their elimination

Code E1 shows the error of the ionization sensor. This happens in the absence of the expected flame. Appears as a result of an unsuccessful ignition of the unit or after a flame breakdown during operation.

E2. Pressure sensor error. Appears as a result of weak traction, which is caused by malfunctions in the operation of the sensor or fan. Within 15 minutes, the unit will try to return to normal work. Check the chimney and the presence of traction in it. If after 15 minutes the error does not disappear, contact the master of the service center.

E3. Error of the thermostat of overheating. Arises in the absence of a coolant or its movement in the heating system. Perhaps the circulation pump is faulty. You should also check all the valves and highways of the system. You can remove the lock using the Mode button. If this does not help, contact the service.

E4. Overheating of temperature sensors. Appears on the screen due to the lack of liquid in the system or its circulation. Check valves and heating highway. The lock is removed using the Mode button.

E5. Temperature sensor error. It comes out with a malfunction of the cold water sensor. Close hot water and wait. Blocking can be removed by pressing the Mode button. Code E6. DIS sensor error. Appears with a malfunction of the sensor. Close hot water taps to normalize the heating system. The lock is removed using the Mode button.

E7 is a problem in a temperature sensor. Displayed when the sensor of the temperature of the heating circuit. Typically, this code appears when a connection with the sensor. When it gets better, the problem disappears.

E8. Indicates the presence of residual fire (error of the ionization sensor). It occurs if the fire remains in the combustion chamber or as a result of the sensor error. Remove the lock using the Mode button. If the error occurs again, contact the service. E9 means the error of the pressure sensor. Appears at low fluid pressure or with its absence. You should check the system for leaks or adjust the speed with which the pump pumps the coolant. It is necessary to eliminate the identified leaks or adjust the operation of the pump.

Arderia gas boilers error codes are malfunctions and what to do to eliminate them

The device and principle of operation of Arderius boilers

The Arderi company produces two types of double.Circuit wall gas boilers. Bittermic and with two separate heat exchangers. The body is metallic, covered on top with white enameled paint. To remove the lid, you need to spin two bolts from below. At the bottom there is a pressure gauge.

The primary heat exchanger is made of high.Quality copper, secondary. From stainless steel. On the left below, the Grundfos pump with a dry rotor is installed, in which there is no contact of the coolant with the electric motor. This prevents clogging and jamming, and also increases the efficiency of the boiler.

Under the burner in front of the combustion camera is a fan operating on direct current. This allows him to work at different speeds and provide the necessary air pressure at the moment. The location in front of the furnace means that it creates not a vacuum, but a boost of air.

The electronic control board has been installed on the bottom right, on which DIP switches are issued. Additionally, the device is equipped with an SMPS chip that performs voltage stabilizer function.

Included to the apparatus is a convenient remote control panel with self.Diagnosis function. It sets the temperature of hot water and coolant.

In the boilers of Ardery of Series “B”, a bittermic radiator is installed, which combines heat exchangers and heating heat exchangers and heating. Inside the main copper pipe with a round section, a thinner, in the form of a rhombus, was inserted.

Gas boiler

Hot water flowing to the water clearance points flows on the internal. In external. Water that plays the role of the coolant in the heating system. Consider the most common codes of the errors of the gas boiler Arderia.

See also  How to vacuum the basin intake frame

The main error codes

Error A2 shows that the thrust is not strong enough. This can be caused by fan breakdown, chimney clogging or air pressure sensor malfunction. It is necessary to check the operability of the fan, inspect and, if necessary, clean the chimney.

Error A3 means that the pressure sensor worked before the circulation pump was turned on. Carefully inspect the sensor and clean it.

Error A4 is displayed when the temperature sensors of Boutem or Warmtem overheat. The reason may be a stopping of the circulation of the coolant or its absence. It is necessary to open the tap tap for warm water to lower the temperature. Check the condition of the highways and valves of the heating circuit.

Temperature sensor

Error A5 means that the coolant pressure is too low. This can be caused by a too small amount of liquid in the heating system, air entering the heating circuit or breakdown of the circulation pump. It is necessary to inspect the system of divorce of the coolant, perhaps somewhere water is dripped from the tube and check the correctness of the pressure sensor.

Error A6 is displayed when roding error. In this case, the ionization sensor does not work due to the lack of flame. Check the gas supply to the boiler, the operation of the gas valve and the transformer of the ignition.

Error A7 shows a gas valve malfunction. Works when the relay is closed. It may also appear in case of breakdown of the control unit.

Error A9 displays the “freezing” signal. The cause of the occurrence is water cooling in the system up to five degrees.

AA error means that the water temperature in the system approaches 100 degrees. This happens when the heating contours are closed, the filter was clogged, the pump is faulty or the three.Way valve was damaged.

Three.Way valve for Arderia boilers

Other malfunctions

Consider what to do with faults when an error is not displayed on the screen:

  • If you felt a clear smell of gas, urgently turn off the boiler, all electrical appliances and overlap the gas valve. After that, call the gas service that will have to check the gas pipeline and the boiler itself. Be sure to open the window and listen carefully to yourself, as there is a danger of carbon monoxide poisoning.
  • After turning on the device, the fan begins to work, and the flame in the burner does not appear. Perhaps too low voltage in the mains. You can check this with a voltmeter. To eliminate this problem, set an additional voltage stabilizer.

It is also important to inspect the chimney for clogging and foreign objects. This also leads to a malfunction of the air pressure switch and the lack of tightness in the combustion chamber.

Each model of the gas boiler Arderia has its own personal characteristics. To avoid most problems during operation, carefully read the instructions for your equipment.

Operating principle

Arderia heating gas boiler has two varieties: it can have one Bittermic heat exchanger or two radiators. The first type differs in that water simultaneously heats up for both water supply and heating.

The second type consists of two knots. They are heated by each individually. One radiator is made of copper, the second. From stainless steel. Water circulation occurs using a pump. The removal of combustion products is also forced. It occurs using a special fan.

The management of such gas boilers can be both electronic and remote. Remote control is always sold in the kit.

All gas heating boilers Arderia have a number of features that include:

  • This equipment is completely suitable for Russian heating systems;
  • The boilers have a special voltage stabilizer, which helps the device to work uninterruptedly even with voltage surges;
  • The boilers have a gearbox that stabilizes the work when the gas pressure falls;
  • Arderia gas heating boilers are practical, stylish and are of high quality.

The scheme of the principle of operation of these boilers is as follows:

  • First of all, you need to set the required temperature using a remote control;
  • The boiler is turned on automatically using the temperature sensor and works until it reaches the set parameters;
  • After that, the sensor turns off the boiler;
  • As soon as the temperature decreases by 15 degrees Celsius, the sensor again turns on the boiler.

The pressure in the boiler is constantly regulated by the air valve, as well as the gas duct sensor.

Recommendations for safe operation

For self.Connection of boilers from gas, certain skills and knowledge in the field of electricians are required. To connect without outside help, you need to know:

  • That for the quality operation of the device you do not need to connect uninterruptions. The built.In stabilizer will follow the work of the controller fee. Nevertheless, it is true to bring the fishing line for the voltage trimmer and the thermal attires are able to connect only a professional.
  • That for the output of the chimney it is worth accurately observed diameter and angles. With any inaccuracies, the effectiveness of the boiler may be violated.
  • That under a warranty agreement, launch and all starting work should be carried out in the presence of gas workers and agents of the company.

Incorrect connection. The basis of most malfunctions of the boilers from gas.

The device and principle of operation of Arderius boilers

The Arderi company produces two types of double.Circuit wall gas boilers. Bittermic and with two separate heat exchangers. The body is metallic, covered on top with white enameled paint. To remove the lid, you need to spin two bolts from below. At the bottom there is a pressure gauge.

The primary heat exchanger is made of high.Quality copper, secondary. From stainless steel. On the left below, the Grundfos pump with a dry rotor is installed, in which there is no contact of the coolant with the electric motor. This prevents clogging and jamming, and also increases the efficiency of the boiler.

Under the burner in front of the combustion camera is a fan operating on direct current. This allows him to work at different speeds and provide the necessary air pressure at the moment. The location in front of the furnace means that it creates not a vacuum, but a boost of air.

The electronic control board has been installed on the bottom right, on which DIP switches are issued. Additionally, the device is equipped with an SMPS chip that performs voltage stabilizer function.

Included to the apparatus is a convenient remote control panel with self.Diagnosis function. It sets the temperature of hot water and coolant.

In the boilers of Ardery of Series “B”, a bittermic radiator is installed, which combines heat exchangers and heating heat exchangers and heating. Inside the main copper pipe with a round section, a thinner, in the form of a rhombus, was inserted.

For what reason the boiler Arderia began to issue E2 error, how to eliminate it

Arderia boiler in work is approximately two to three minutes, after which the burner stops acting, and error E2 is given out. It burns for about a minute, the burner, starts again, and the device continues to function regularly for another 3-4 minutes, and so constantly. This code, referring to the instructions, shows the traction sensor to be respected, although the chimney canal is not polluted, the gases that have worked out are allotted normally. I can’t find out what is the reason for the problem?

See also  How long does a delicate wash take?

In your situation, the main reasons that contribute to the lack of traction are: traction sensor damage. Lack of contact between the Pneumorela sensor and the electronic fee. The presence of condensate, as well as the incorrect fastening of tubes with pneumorelane. The fan has damage. Presumably, there are no required revolutions.

arderia, boiler, does, turn, control, panel
  • Why did Arderia often turn on and turn off when heated
  • What is the problem if Ariston’s gas boiler shows an error 607 on how to drop it
  • How to eliminate the Weland of the F28 code on the Weland boiler
  • Because of which the Vissman boiler does not function for hot water supply
  • How to eliminate error 43 on the Rinnay boiler
  • Because of what he began to heat up and loudly buzz the boiler Neva luxury
  • Because of which the boiler is not working on the hot water
  • How to eliminate the immortal on the gas boiler error 01
  • For what reason the boiler Navien does not work in hot water supply mode
  • How to eliminate ELECTROLUKS on the boiler E1
  • How to eliminate an error with the F37 code on the ferroli boiler
  • How can be eliminated on a gas boiler Buderus error 6a
  • Because of what the Daewoo gas boiler stopped maintaining pressure
  • Why does the Bosch gas boiler do not function on the hot water
  • What is the malfunction of the Baxi boiler if it gives an error e01
  • Beretta gas boiler does not keep pressure, what is the reason
  • What is the malfunction of the Arderia gas boiler if it began to give out error A6
  • Ariston reduces the pressure in the gas boiler, what are the reasons
  • For what reasons can he bask and buzz the boiler Rinnai
  • Why the Vissman boiler was constantly turning on and off
  • Due to which the boiler of Arderia does not function in the mode of the hot water
  • For what reasons, the wall boiler Ariston began to give an error with code 501
  • What is the problem if the boat baked gives an error E03, and how to fix it
  • Why does the boiler boiler give out a 3C error, how to drop it
  • Why often turns off and the boiler is turned on when heated
  • What is the malfunction of the Ariston boiler if he shows error 607
  • How can you eliminate a mistake with code 10 on the boiler 10
  • What is the problem with the electrician boiler if it gives out error code E3
  • How to eliminate the F36 error on the Gas C boilery
  • What is the problem with the gas boiler wrapper if it gives an error F25
  • How to eliminate a bisman on a gas boiler error with the F5 code
  • What is the malfunction of the boiler ferroli if it shows a mistake with the F05 code
  • How to eliminate an error e03 on the boiler
  • What is the breakdown of the boiler Bosch if it shows an error C6
  • What is the breakdown of the gas boiler if it gives out error code 3s
  • What is the problem if the Rinnay boiler gives out error 99, and how to fix it
  • For what reason the boiler Beretta gives an A03 error, how to eliminate it
  • Why is the junkers boiler in heating mode constantly turn off and turns on
  • Why is the Daewoo boiler is constantly turned off when heated
  • Why is the boiler Bosch constantly turn on and turns off when heated
  • Because of which the boiler of thermon often turns off and turns on when heated
  • Because of which the Celtic boiler when heated is constantly turned on and turns off
  • What is the malfunction of the gas boiler Wesen if it gives an error E01
  • How to eliminate a Koreasastar on a gas boiler error with A01 code
  • How to eliminate the senior duval error with the F1 code on the gas boiler
  • How to eliminate a Celtic gas boiler error with A6 code
  • What is the Elsotherm boiler malfunction if it began to issue E1 error
  • For what reasons, the Bugatti gas boiler began to give out error E01
  • How can you eliminate a motan error with the E2 code on the boiler
  • Why does the Immergaz boiler drop in pressure
  • For what reason did the gas boiler stop the pressure with kitur
  • In the gas boiler of Korea, the old pressure drops, what are the reasons
  • Why does the boiler do not keep the pressure of the mora
  • In the boiler Navien, the pressure is reduced, what is the malfunction
  • In the gas boiler, the tank decreases the pressure, what are the reasons
  • Because of which the rinnai boiler does not keep pressure
  • For what reasons, the boiler Ariston gives out error code 101
  • How to eliminate a f20 error on the boiler
  • For what reasons, the Daewoo gas boiler shows an error with the E3 code
  • How to eliminate the Navien error with code 16 on the boiler
  • For what reasons, the boiler electrolyux gives an error E2
  • How to eliminate a Weilant Error F20 on a gas boiler
  • What is the problem with the beretta boiler if he began to give out error A02
  • How to eliminate a bisman error f2 on a boiler
  • For what reasons, the Neva boiler luxury shows the error code 02
  • How can I eliminate the Ferroli boiler A03 error
  • For what reasons, the gas boiler of the Baxi shows the error e02
  • How can be eliminated on a gas boiler Bosch Error E9
  • For what reasons, the gas boiler Buderus gives an error 2e
  • How to eliminate the oasis Error E3 on the boiler
  • For what reasons, the rinnai boiler shows error 16

Arderia boiler does not start. Malfunctions and ways to eliminate them, what to do if the pressure drops

Errors of gas boilers Arderia and methods for their elimination

Any gas boiler needs regular care and preventive measures. It happens that external factors become the causes of malfunctions: low pressure in the highway, tension changes, etc.

The malfunctions of gas double.Circuit wall boilers Arderia are detected in the form of codes on the screen. Their decryption is in the operating instructions.

Error code Cause How to eliminate
A1 Closing the air sensor of the pressure (blowing up the chimney). It usually occurs when clogging the smoke channel or the appearance of a reverse traction It should be examined if the chimney is clogged with garbage, whether ice was formed on it, which interferes with the yield of smoke and the flow of air to the burner.
See also  How to choose the boiler capacity for the house

Check the presence of reverse traction, if any, you should identify the cause of the appearance. Perhaps you need to put the deflector on the pipe or change the design of the chimney

Appears due to a malfunction of the element, a break in its wiring

It is necessary to check the operability of the fan, does it prevent him from. If necessary, clean the part of garbage.

Perhaps at the end of the coaxial pipe there was an ice that prevents the exit of it from it

A3 Problems in the circulation pump and its sensor

Often occurs if the pressure sensor is clogged

Check the sensor wiring and diagnose the pump.

If necessary, clean and connect the wires

Central Boiler: Final issue solved! Temperature Sensor and Controller

Perhaps all shut.Off valves of the heating system are closed

arderia, boiler, does, turn, control, panel

Unlock the circulation pump and cleanse its visible parts from garbage.

Check the operability of the three.Way valve and the sensor of the hydraulic duct.

It is necessary to remove air traffic jams using the crane of the Maevsky.

The speed speed of the circulation pump should be adjusted.

A6 There is no ignition. The smoke pipe is blocking.

Typically, the reason for the failure of the control board

Diagnosis of the gas valve and its wiring.

If necessary, replacing a broken part with a new

A8 There is a residual flame in the combustion chamber, although the voltage is not supplied to the gas valve.

The reason lies in the problems of the diaphragm of the gas valve

In case of malfunction of the valve diaphragm, it is replaced. If this did not help, you should change the control board A9 Freezing. The temperature of the coolant reached

If the unit has not earned automatically, you should turn it on Aa Boiling. The temperature of the liquid in the system exceeded the permissible.

Perhaps this happened for the following reasons:

Check the performance of the pump and three.Way valve

Stripping contacts and supplying them to the thermostat.

It mainly occurs as a result of clogging of the chimney or its deformation.

Models of gas boilers Arderia B10, B14, B16 have other errors codes. Consider what they mean and how to eliminate the malfunctions.

E0. Anti.Frustration mode. This code is displayed on the screen if the temperature of the coolant dropped below 1 ° C. It is necessary to check the integrity of the system in which the liquid circulates. The error disappears if the coolant is heated. If it has not disappeared, call the master.

The gas boiler does not gain temperature. The causes and methods of their elimination

Find out here why the gas boiler does not light up?

Why the gas boiler works without stopping. The reasons and methods of their elimination

Code E1 shows the error of the ionization sensor. This happens in the absence of the expected flame. Appears as a result of an unsuccessful ignition of the unit or after a flame breakdown during operation.

E2. Pressure sensor error. Appears as a result of weak traction, which is caused by malfunctions in the operation of the sensor or fan. Within 15 minutes, the unit will try to return to normal work. Check the chimney and the presence of traction in it. If after 15 minutes the error does not disappear, contact the master of the service center.

E3. Error of the thermostat of overheating. Arises in the absence of a coolant or its movement in the heating system. Perhaps the circulation pump is faulty. You should also check all the valves and highways of the system. You can remove the lock using the Mode button. If this does not help, contact the service.

E4. Overheating of temperature sensors. Appears on the screen due to the lack of liquid in the system or its circulation. Check valves and heating highway. The lock is removed using the Mode button.

E5. Temperature sensor error. It comes out with a malfunction of the cold water sensor. Close hot water and wait. Blocking can be removed by pressing the Mode button. Code E6. DIS sensor error. Appears with a malfunction of the sensor. Close hot water taps to normalize the heating system. The lock is removed using the Mode button.

Repair

Of course, thanks to the control panel and the display on which the code of error arising in the gas boiler is displayed, it becomes possible to quickly eliminate it. You can do this with your own hands or use the help of professionals or service center.

To independently get rid of the problem that has arisen, you can use the following ways to eliminate the most common errors in the Arderia gas heating boilers.

  • When you turn off the chimney pressure sensor, it is necessary to clean the output.
  • If there is a decrease in the number of revolutions of the fan, you need to check the presence of foreign particles on its blades. After cleaning it, the problem will be solved.
  • When turning on the overheating sensor, it is better to replace the heat exchanger.
  • If reduced pressure occurs, it is necessary to check the performance of the pump, as well as the tightness of all valves. You may have to remove the old gaskets and put new ones, be sure to consider the sizes of the sealing rings, as well as change the valve. This will help correct the error and increase the pressure in the boiler.
  • If you block the ignition, it is necessary to remove the spare parts of the gas valve, check their performance. Perhaps they will have to be replaced.
  • If the boiler is not turned on, and the burner works, it is necessary to check the setting of the electronic control unit: it could break. In this case, it will have to be replaced.
  • If sharp changes in water temperature appear, you need to clean the filters, as well as check the pump and a water current sensor.

Arderia gas heating boilers are equipped with a malfunction diagnostic system that allows you to find out exactly what has happened for a breakdown, and also quickly solve the problem that has arisen. In this case, it is recommended to apply the instructions for the operation of equipment.

As for the reviews of the owners of these units, then, in addition to all advantages, they distinguish some shortcomings that can be attributed:

  • The boilers work loud enough;
  • Hot water flows after a large period of time;
  • Pump, the control unit can become unusable ahead of time;
  • Simple and uninteresting boilers design.

About how to do the preventive work of the Arderia boiler about how to do it with your own hands, watch in the next video.

| Denial of responsibility | Contacts |RSS